Sold individually - you will need 6 for a full set.

Clutch Lever Switch - RD03/04/07/07A (1988 - 03) - Aftermarket alternative to Honda #35330MK5003

Corrosion Block Grease has the same corrosion protection properties as ACF-50 but in grease form. Can be used as an assembly grease (for example did you know that the copper in copper grease corrodes alloy?) so use this for such things as engine/transmission cases, caliper bolts, wheel bearings, wheel axle bolts (which always seem to corrode), battery terminals, side and centre stands, foot pegs, brake and clutch lever pivots, etc. etc.

Corrosion Block is an anti-corrosion compound developed exclusively to stop existing corrosion and prevent new. It is unique in that it is designed for use in electrics and electronics as well as metals and structures. This makes this product essential for your day-to-day routine maintenance and as long-term asset protection for your boat/equipment within the harsh marine environment.

What will it actually do? It will, with regular applications, make maintenance easier and save you money, easier to clean, look better, help prevent surface/structural/electrical corrosion related failure thereby increasing reliability and it will increase the bike’s value. It will significantly reduce your replacement, repair and labour expenses. That’s what it will actually do!

The Facts:
• KILLS existing corrosion
• PREVENTS new from forming
• Long lasting LUBRICANT
• APPROVED for ELECTRONICS
• Non-Toxic & Environmentally Friendly

Where to use it

Corrosion Block is simply applied to the structure, joints and welds, i.e. under hidden areas, where the corrosion works away un-noticed, under panels and on hidden parts of the engine, gear boxes, generators, switch panels and avionics, especially on outboard engines where it will work hard to prevent corrosion and structural degeneration. Where corrosion is already evident it will help inhibit further progress by insulating and electrically ‘switching off’ the corrosion cell. It will also penetrate around bolts, screws and hardware, protecting them from electrolytic corrosion and preventing seizure.

It will protect electrical joints, plugs and components and prevent corrosion causing high resistance joints. This goes for PCB’s and electronics as well, such as computerised ignition and fuel control units and their multi pin plugs, radio’s, radar and antenna’s, while switches, controls and levers will all be lubricated as well as protected from corrosion. It does not affect the working of electrical or electronic components however keep it off LCD’s. Multi pin plugs and connectors benefit from having Corrosion Block applied directly to the contacts. Corrosion Block has restored many a failed electronic/electrical component. It’s uses are unending, you will love it!

If they have become hard or broken and you have free play, replace them!

New cush drive rubbers will give a smooth feel on the transmission and reduce snatching on acceleration and low revs.

These decals are made from highly reflective vinyl

Size 90mm wide x 125mm high

These decals are made from highly reflective vinyl

Size 90mm wide x 125mm high

Dakar Leather Toolbag

This bag is an exact replica of the leather toolbags that competitors used in the Dakar during the 1980’s.

Manufactured locally in the New Forest by a Master Saddler in 5mm English Oak Bark Tanned Bridle Leather and 100% hand stitched, this is a very high quality Toolbag that will last you a lifetime.  We will also provide a tin of leather care so you can keep it in tip top condition.

The top of the bag is double-folded with strong velcro, giving exta durability and weather resistance.  Strap buckles are brass.

Base of the bag is additionally strengthened with a handstitched 5mm leather patch, meaning it won't lose shape or wear away when in use.

To attach to your bike, just pop the 2 straps under your rack and it's ready to go.

Approximate size is 20cm long (front to rear), 26cm wide (left to right), and 14cm high (top to bottom).  Please note that sizes may vary slightly as each is handcut and stiched.

D.I.D has merged their Professional O-Ring V Series and their top selling Premium X-Ring® VM Series into “ONE” New Pro-Street X-Ring® VX Series. Created from the severe demands of today’s top World Superbikes, D.I.D is proud to introduce this New high performance VX Series. In developing this new series, D.I.D focused on improving “Rigidity”.
Traditionally, “Tensile Strength” has been used to indicate the overall strength of a chain. But Tensile Strength is only a laboratory static measurement of a chain’s “breaking point”. Rigidity, on the other hand, is the ability of a chain to withstand forces that occur in a rider’s real world experience. Increased rigidity means better power transfer from the engine to the ground and greater resistance to stretching under load. This translates into smooth handling and quicker response time.
To maximize performance, D.I.D’s race proven X-Ring® design delivers overall improved performance that meets the demands of today’s high-performance machines. The VX Series is the ultimate in performance and durability, and are a perfect match for your dual sport, sport bike or sport touring bike.

The 525 VX Series chain is suitable up to a maximum engine size of 900cc.

DID's VX Chain uses patented X-ring seals. Like O-rings, X-rings function to seal in lubrication and keep dirt out.

Where the cross section of an O-ring is circular, the cross section of an X-ring is 'X' or cross shaped. This gives the seal additional contact points compared to the O ring, offering superior sealing and protection against dirt and grit getting stuck under the seal.
In addition, when under pressure an O-ring becomes squashed and causes friction. An X-ring, when under pressure, diverts this pressure by twisting instead, so an X-ring decreases friction between side plates and reduces power loss by 50% of any other type O-ring chain.

Half the Power Loss (Compared with Normal O-Ring)

D.I.D’s PATENTED X-Ring construction reduces friction by twisting between the side plates instead of being squashed. Normal O-Rings and other makers’ modified O-Rings have squashed points that increase friction. The twisting action of the X-Ring disperses the pressure and minimizes power loss.

DID's X-rings have 40% greater Wear Resistance (Compared with Normal O-Ring)

The X-Ring’s four contact points greatly increase its sealing performance, keeping the dirt out and the lubrication in much better than any other O-Ring. X-Rings have the greatest wear resistance of any other type of O-Ring or Non-O-Ring chain, this means more resistance to stretching, bowing and warping and smoother handling. With the proper maintenance an X-ring chain will last longer than any O-ring or unsealed chain.

D.I.D has merged their Professional O-Ring V Series and their top selling Premium X-Ring® VM Series into “ONE” New Pro-Street X-Ring® VX Series. Created from the severe demands of today’s top World Superbikes, D.I.D is proud to introduce this New high performance VX Series. In developing this new series, D.I.D focused on improving “Rigidity”.
Traditionally, “Tensile Strength” has been used to indicate the overall strength of a chain. But Tensile Strength is only a laboratory static measurement of a chain’s “breaking point”. Rigidity, on the other hand, is the ability of a chain to withstand forces that occur in a rider’s real world experience. Increased rigidity means better power transfer from the engine to the ground and greater resistance to stretching under load. This translates into smooth handling and quicker response time.
To maximize performance, D.I.D’s race proven X-Ring® design delivers overall improved performance that meets the demands of today’s high-performance machines. The VX Series is the ultimate in performance and durability, and are a perfect match for your dual sport, sport bike or sport touring bike.

The 525 VX Series chain is suitable up to a maximum engine size of 900cc.

DID's VX Chain uses patented X-ring seals. Like O-rings, X-rings function to seal in lubrication and keep dirt out.

Where the cross section of an O-ring is circular, the cross section of an X-ring is 'X' or cross shaped. This gives the seal additional contact points compared to the O ring, offering superior sealing and protection against dirt and grit getting stuck under the seal.
In addition, when under pressure an O-ring becomes squashed and causes friction. An X-ring, when under pressure, diverts this pressure by twisting instead, so an X-ring decreases friction between side plates and reduces power loss by 50% of any other type O-ring chain.

Half the Power Loss (Compared with Normal O-Ring)

D.I.D’s PATENTED X-Ring construction reduces friction by twisting between the side plates instead of being squashed. Normal O-Rings and other makers’ modified O-Rings have squashed points that increase friction. The twisting action of the X-Ring disperses the pressure and minimizes power loss.

DID's X-rings have 40% greater Wear Resistance (Compared with Normal O-Ring)

The X-Ring’s four contact points greatly increase its sealing performance, keeping the dirt out and the lubrication in much better than any other O-Ring. X-Rings have the greatest wear resistance of any other type of O-Ring or Non-O-Ring chain, this means more resistance to stretching, bowing and warping and smoother handling. With the proper maintenance an X-ring chain will last longer than any O-ring or unsealed chain.

DOT 4 Universal Hydraulic Brake & Clutch Fluid is a high quality brake and clutch fluid, blended from superior materials to a high standard of purity.

Features
Suitable for use in all motor vehicles and motorcycles made in the UK, USA, Europe and Japan
It cannot be used in vehicles requiring mineral based fluids
Mixes safely with the SAE J1703, DOT 3 and DOT 4 brake fluids
DOT 4 is designed to meet the stringent demands of the following specifications:
• SAE J1703, SAE J 1704
• US FMVSS 116 DOT 4 AND DOT 3.
• ISO 4925

Caution:
Brake fluid can damage vehicle paintwork and it must be washed off with water immediately. It is also necessary to keep the container tightly sealed to prevent absorption of moisture.
Contamination with dirt, water, petroleum products or other materials may result in brake failure or costly repairs.

Typical Physical Characteristics
• Density @ 20C - 1.050
• Equilibrium reflux boiling point - 243 C
• Wet equilibrium boiling point - 160 C
• Viscosity @ -40C -1296 cSt
• Viscosity @ 100C - 2.17 cSt
• Appearance - Clear Pale Amber Liquid
• Product code 14420