Connect the Denali DataDim™ Controller in place of the original relay to enable the lights to switch between half and full intensity with your vehicles original high beam switch.

This DENALI DataDim Dual-Intensity Controller enables the DENALI lights to switch between half and full intensity with your vehicle's original high beam switch.

All DENALI 2.0 Light pods are equipped with a dedicated 3rd-wire dimming circuit so we can use an external signal to reliably control the intensity of the LED chip at the source.

 
What's In The Box?

• (x1) DataDim Dual-Intensity Controller
• (x1) Dual-Intensity Trigger Wire

• LEDs: 10 watt Cree XPL HI (per lamp)
• Power Draw: 1.6 amps total
• Beam Distance (spot): 1000ft
• Beam Width (spot): 75ft
• Raw Lumens: 2190
• Intensity: Single Intensity Harness
• DataDim™ Compatible: yes
• Operating Voltage: 12v
• Pod Size 3.7in diameter x 3.8in deep

• (2) LED Light Pods
• (2) Spot lenses (pre-installed)
• (2) E-Mark approved True-Hybrid™ lenses 
• (1) HotSwap™ single intensity wiring harness with the capability of a plug-and-play hot swap to dual intensity without changing the harness itself
• (1) DrySeal™ waterproof illuminated switch
• (1) 7/8in handlebar switch mount
• (1) 1in handlebar switch mount
• (2) hinge mounts with M8 stainless steel hardware
• (4) Zip ties & (1) adhesive mounting square

• Mountable on crashbar or other tubular parts with suitable diameter
• Made of fibre-reinforced Nylon
• Inclusive rubber insert adapters for diameter 22 mm, 25,4 mm, 26 mm, 27 mm and 28 mm
• Color: Black

• 2 crash bar clamps for lights
• 4 rubber insert adapters
• Mounting material
• Mounting instructions

• (2) LED Light Pods
• (2) Spot lenses (pre-installed)
• (2) E-Mark approved True-Hybrid™ lenses 
• (1) HotSwap™ single intensity wiring harness with the capability of a plug-and-play hot swap to dual intensity without changing the harness itself
• (1) DrySeal™ waterproof illuminated switch
• (1) 7/8in handlebar switch mount
• (1) 1in handlebar switch mount
• (2) hinge mounts with M8 stainless steel hardware
• (4) Zip ties & (1) adhesive mounting square

This is a complete Plug and Play Denali Dual Intensity LED Light Kit with the OEM Honda Fog Light Switch already built into the loom.

The kit contains the following

• 1 x OEM Honda Fog Light Switch
• 2 x Denali D2 LED Dual Intensity Light Pods
• 1 x Denali DataDim Dual Intensity Controller Module
• 1 x Plug and Play Wiring Loom

This means that there is no cutting or tapping into the existing wiring on your CRF1000 or CRF1000 Adventure Sport - you just plug this kit into existing connectors that are already in your bike's wiring loom.

The loom also has a connector allowing the fitment of the OEM Honda Auxilliary Power Socket as well or power a GPS.

• Engine Running / Fog Light Switch OFF / Denali Lights OFF
• Engine Running / Fog Light Switch ON / Denali Lights on at 50% DRL level
• Engine Running / Fog Light Switch ON / Main Beam ON (or flasher switch pressed) / Denali Lights on at 100%

Very neat install with no excess loom to try and find space for - specifically manufactured for the Honda CRF1000 Afria TWin and Adventure Sport.

Fits all models of CRF1000 Africa Twin, and CRF1000 Adventure Sport.

Denali 2.0 Light Kits are brighter, more robust, and a lot more versatile.

The all new Cree High-Intensity 10 watt LED's are focused through our TriOptic Lens System to give you three unique beam patterns in one kit.

Equipped with DataDim Technology and a modular HotSwap wiring harness, the lights can switch between half and full intensity with your vehicle's original high beam switch.

Our DrySeal submersible waterproof construction and Impact PC Bezels create super durable light and switch housings that can withstand the most extreme environments without giving up. 

 
DENALI 2.0 Features 

• HiDrive High-Intensity Cree LED's 
• TriOptic Multi-Beam Lens System 
• DataDim LED Dimming Technology 
• HotSwap Modular Wiring Harness System
• DrySeal Submersible Waterproof Light Housings 
• Impact PC Corrosion-Proof Bezels
• LiveActive Intelligent Thermal Management
• Chrome Plated Optic Holders
• Low-Profile Mount with Stainless Steel Hardware
• E Mark Lenses Included

Features Explained:

HiDrive High-Intensity 10 Watt LED's:
2.0 lights feature the latest development from Cree; a new Hi-Intensity LED chip that features a redesigned primary optic to maximize light output through secondary optics. The “HI” series LEDs are more efficient; producing more lumens and 15% more light output without increasing power draw.  

TriOptic Multi-Beam Lens System:
2.0 Light kits include two spot lenses and two elliptical flood lenses giving you three unique beam patterns in one kit. Use two spots for maximum distance, two elliptical floods for maximum spread, or one of each for the best of both worlds. 

Data Dim LED Dimming Technology:
All 2.0 light pods are equipped with a dedicated 3rd-wire dimming circuit so we can use an external signal to reliably control the intensity of the LED chip at the source.   Plug in our DataDim Controller (sold separately) to enable the DENALI lights to switch between half and full intensity with your vehicle's original high beam switch. 

Data-Dimming eliminates unnecessary modulation of the entire circuit which is unavoidable using basic two-wire dimming.     

DrySeal Submersible Waterproof Light Housings:
In addition to molded silicone gasket seals, we use a unique DrySeal construction technique that encases the wires in a potted cavity as they enter the housing. This ensures our housings are 100% watertight even when submerged underwater with the wires cut and connector removed.  

Impact PC Corrosion-Proof Bezels:
Our Impact PC bezels are molded in 100% polycarbonate to create an impenetrable surface that won't rust, fade, or corrode even after taking repeated impacts from rocks and debris. 

LiveActive Intelligent Thermal Management:
DENALI 2.0 lights feature cutting edge LED drivers that work with our uncompromising heatsinks to manage heat levels in real time. This duo works together to ensure that our lights stay cool enough to maintain the maximum light output when you need it most. 

Chrome Plated Optic Holders:
We take the extra step to chrome plate our optic holders to maximize reflectivity and refine the appearance match the original chrome reflectors of your vehicle headlights. 

Low-Profile Mount with Stainless Steel Hardware:
DENALI 2.0 light pods include a robust, low-profile hinge mount and stainless steel M8 mounting hardware. The low-profile hinge creates a super clean installation while maintaining maximum strength. 

E Mark Approved Lenses
DENALI 2.0 kits include E Mark approved lenses

 
D2 Product Specs:

• LED's: (2x) 10 Watt Cree XPL HI
• Power Draw: 1.6 Amps
• Beam Distance (Spot): 525 Feet
• Beam Width (Spot): 75 Feet
• Raw Lumens: 2190
• Intensity: Single Intensity Harness
• DataDim Compatible: Yes 
• Operating Voltage: 12 VDC
• Pod Size:  2.2" Round x 2.4" Deep

This is a complete Plug and Play Denali Dual Intensity LED Light Kit with the OEM Honda Fog Light Switch already built into the loom.

The kit contains the following

• 1 x OEM Honda Fog Light Switch
• 2 x Denali D4 LED Dual Intensity Light Pods
• 1 x Denali DataDim Dual Intensity Controller Module
• 1 x Plug and Play Wiring Loom

This means that there is no cutting or tapping into the existing wiring on your CRF1000 or CRF1000 Adventure Sport - you just plug this kit into existing connectors that are already in your bike's wiring loom.

The loom also has a connector allowing the fitment of the OEM Honda Auxilliary Power Socket as well or power a GPS.

• Engine Running / Fog Light Switch OFF / Denali Lights OFF
• Engine Running / Fog Light Switch ON / Denali Lights on at 50% DRL level
• Engine Running / Fog Light Switch ON / Main Beam ON (or flasher switch pressed) / Denali Lights on at 100%

Very neat install with no excess loom to try and find space for - specifically manufactured for the Honda CRF1000 Afria TWin and Adventure Sport.

Fits all models of CRF1000 Africa Twin, and CRF1000 Adventure Sport.

DENALI DR4 2.0 LED TriOptic™ LED light

Denali 2.0 Light Kits are brighter, more robust, and a lot more versatile.

The all new Cree High-Intensity 10 watt LED's are focused through our TriOptic Lens System to give you three unique beam patterns in one kit.

Equipped with DataDim Technology and a modular HotSwap wiring harness, the lights can switch between half and full intensity with your vehicle's original high beam switch.

Our DrySeal submersible waterproof construction and Impact PC Bezels create super durable light and switch housings that can withstand the most extreme environments without giving up. 

 
DENALI 2.0 Features 

• HiDrive High-Intensity Cree LED's 
• TriOptic Multi-Beam Lens System 
• DataDim LED Dimming Technology 
• HotSwap Modular Wiring Harness System
• DrySeal Submersible Waterproof Light Housings 
• Impact PC Corrosion-Proof Bezels
• LiveActive Intelligent Thermal Management
• Chrome Plated Optic Holders
• Low-Profile Mount with Stainless Steel Hardware
• E Mark Lenses Included

Features Explained:

HiDrive High-Intensity 10 Watt LED's:
2.0 lights feature the latest development from Cree; a new Hi-Intensity LED chip that features a redesigned primary optic to maximize light output through secondary optics. The “HI” series LEDs are more efficient; producing more lumens and 15% more light output without increasing power draw.  

TriOptic Multi-Beam Lens System:
2.0 Light kits include two spot lenses and two elliptical flood lenses giving you three unique beam patterns in one kit. Use two spots for maximum distance, two elliptical floods for maximum spread, or one of each for the best of both worlds. 

Data Dim LED Dimming Technology:
All 2.0 light pods are equipped with a dedicated 3rd-wire dimming circuit so we can use an external signal to reliably control the intensity of the LED chip at the source.   Plug in our DataDim Controller (sold separately) to enable the DENALI lights to switch between half and full intensity with your vehicle's original high beam switch. 

Data-Dimming eliminates unnecessary modulation of the entire circuit which is unavoidable using basic two-wire dimming.     

DrySeal Submersible Waterproof Light Housings:
In addition to molded silicone gasket seals, we use a unique DrySeal construction technique that encases the wires in a potted cavity as they enter the housing. This ensures our housings are 100% watertight even when submerged underwater with the wires cut and connector removed.  

Impact PC Corrosion-Proof Bezels:
Our Impact PC bezels are molded in 100% polycarbonate to create an impenetrable surface that won't rust, fade, or corrode even after taking repeated impacts from rocks and debris. 

LiveActive Intelligent Thermal Management:
DENALI 2.0 lights feature cutting edge LED drivers that work with our uncompromising heatsinks to manage heat levels in real time. This duo works together to ensure that our lights stay cool enough to maintain the maximum light output when you need it most. 

Chrome Plated Optic Holders:
We take the extra step to chrome plate our optic holders to maximize reflectivity and refine the appearance match the original chrome reflectors of your vehicle headlights. 

Low-Profile Mount with Stainless Steel Hardware:
DENALI 2.0 light pods include a robust, low-profile hinge mount and stainless steel M8 mounting hardware. The low-profile hinge creates a super clean installation while maintaining maximum strength. 

E Mark Approved Lenses
DENALI 2.0 kits include E Mark approved lenses

This is a complete Plug and Play Denali Dual Intensity LED Light Kit with the OEM Honda Fog Light Switch already built into the loom.

The kit contains the following

• 1 x OEM Honda Fog Light Switch
• 2 x Denali S4 LED Dual Intensity Light Pods
• 1 x Denali DataDim Dual Intensity Controller Module
• 1 x Plug and Play Wiring Loom

This means that there is no cutting or tapping into the existing wiring on your CRF1000 or CRF1000 Adventure Sport - you just plug this kit into existing connectors that are already in your bike's wiring loom.

The loom also has a connector allowing the fitment of the OEM Honda Auxilliary Power Socket as well or power a GPS.

• Engine Running / Fog Light Switch OFF / Denali Lights OFF
• Engine Running / Fog Light Switch ON / Denali Lights on at 50% DRL level
• Engine Running / Fog Light Switch ON / Main Beam ON (or flasher switch pressed) / Denali Lights on at 100%

Very neat install with no excess loom to try and find space for - specifically manufactured for the Honda CRF1000 Afria TWin and Adventure Sport.

Fits all models of CRF1000 Africa Twin, and CRF1000 Adventure Sport.

DENALI S4 2.0 TriOptic™ LED Light Pods